Select a continuous wave fiber laser source for plastic processing by matching wavelength to material absorption, then defining the delivered power, beam geometry, and exposure needed for an acceptable thermal result. For clear-plastic welding, the objective is a repeatable joint with controlled heating of the surrounding part.
A 1940 nm thulium fiber laser is a candidate when the production polymer absorbs sufficient energy at that wavelength to support the intended joint geometry. Equipment OEMs should develop material response, optical exposure, and fixture conditions together. This establishes the process window needed to select a source configuration and specify its operating range.
Visible clarity describes a material’s response to visible light. Laser welding depends on its optical behavior at the processing wavelength. Polymer chemistry, crystallinity, additives, scattering, and thickness all influence how radiation reaches and heats the joining region.
Near 2 µm, some polymers have sufficient intrinsic absorption to enable welding without an added laser absorber. Research using thulium fiber laser radiation demonstrated absorber-free welding of selected polymers after characterizing their optical properties and developing suitable processing conditions.
For an OEM project, the material specification should identify the resin grade, additives, colorants, and representative wall thickness. Optical measurements on that material can establish how much radiation is transmitted and absorbed through the intended path. Include the as-manufactured condition, since surface finish and molded geometry may differ from laboratory coupons.
The required information is specific to the joint. A beam entering through a thick wall encounters a different optical path from one passing through a thin cover. The source wavelength and processing optics must support heating at the intended depth while preserving nearby features and surfaces.
Conventional transmission welding commonly directs radiation through an upper component to an absorbing lower component. At wavelengths near 2 µm, clear-to-clear welding can involve absorption within both joining parts, creating a different heating distribution.
Focusing, optical path length, and joint location therefore belong in the same design review. Stronger absorption can favor heating nearer the entry surface; greater penetration can distribute energy through more material. The appropriate distribution is the one that produces the required joint while maintaining acceptable conditions elsewhere in the part.
Define the joint geometry, joining materials, permitted distortion, and performance after cooling. A sealed enclosure may prioritize leak performance; a structural connection may prioritize mechanical loading. Appearance and dimensional limits can constrain the thermal cycle even when the joint meets its strength target.
Fixture design maintains contact between the joining surfaces and controls component position. Clamping pressure is a recognized variable in polymer laser-welding development because contact affects heat transfer and joint formation.
The fixture must provide optical access while supporting the part around the weld. Its contact surfaces, compliance, and loading sequence should reflect the production geometry. Flat coupons help establish initial settings, while representative components reveal the effects of curvature, local stiffness, and assembly tolerances.
Include release timing in the process sequence. The joint’s condition during cooling and handling is part of the manufacturing cycle, so fixture operation should be developed alongside laser exposure.
For a stationary exposure at constant power, incident energy equals delivered optical power multiplied by exposure time. For a constant-speed scan, incident energy per unit path length equals delivered power divided by speed. Polymer welding studies use this line-energy relationship to organize processing conditions.
Delivered power refers to power reaching the defined processing plane after optical transmission losses. Absorbed energy depends additionally on the material and the beam’s path through it. Keeping those quantities distinct connects source selection with the thermal result at the joint.
Line energy is a useful comparison parameter, but the beam geometry and exposure history must accompany it. Two settings with equal energy per unit length can produce different temperature distributions when power, speed, spot dimensions, or absorption differs.
Irradiance is incident optical power per unit area. The beam profile and spot-size definition determine how that power is distributed across the processing region. For a nonuniform profile, peak irradiance differs from an average calculated over a chosen area.
Record beam dimensions, profile, focal position, scan speed, and power with each trial. For a scanned spot, its dimension along the travel direction and the scan speed influence local exposure time. The transverse dimension helps define the region heated across the joint.
At corners and during acceleration, motion can change while power remains constant. The exposure strategy should address these regions explicitly so that local heating remains within the qualified window.
Establish the acceptable delivered-power range before choosing the source rating. The source must cover the upper end after optical losses and provide suitable control at the lower settings used by the process.
Size the power margin to cover measured optical transmission losses and any additional output required by qualified production recipes. The corresponding low-power adjustment range, resolution, repeatability, and response are equally important when several recipes share the same platform.
Document output settling after a command change and emission behavior at scan start and stop. These transitions should reproduce the exposure conditions used to qualify the joint.
Menovex’s 60W CW thulium fiber laser and 120W CW thulium fiber laser are candidates for transparent-plastic welding and cutting applications. Both operate at 1940 ± 10 nm and use water cooling.
Compare the two configurations against the required delivered-power range, optical transmission losses, and production recipes. Confirm the continuous-output adjustment range, low-power control, and stability conditions for the selected configuration.
A higher power class becomes relevant where the qualified process requires additional output. For a machine running multiple parts, compare both the highest-power recipe and the lowest required setting. The selected configuration should support the full operating range with the control behavior needed by each recipe.
Both configurations support CW and pulsed operation. Define CW requirements independently, including continuous output, adjustment behavior, and stability under agreed measurement conditions.
The processing optics must be suitable for 1940 nm operation and the required power distribution. Beam diameter, divergence, output geometry, and M² provide inputs for selecting the optical arrangement. The resulting heated region should be evaluated on the actual part geometry.
A defined power-measurement plane separates source performance from transmission losses through the machine. Recording that location makes trial results and later maintenance checks comparable.
For the water-cooled source, specify coolant temperature, flow, pressure, water quality, and heat-removal capacity using configuration-specific installation data. Confirm these conditions during sustained machine operation, including any other loads served by the cooling system.
Thermal control and optical control work together. A production recipe should identify the output setting, motion or exposure time, fixture conditions, and cooling conditions required to reproduce the accepted joint.
Transparent-plastic cutting requires its own process window, even where a source is also evaluated for welding. The required outcome is complete separation with acceptable contour accuracy, kerf, and edge condition.
Develop exposure, support, and motion around those requirements. Part stability can change as a contour approaches completion, and the released component must be handled without damaging the new edge or adjacent features.
Evaluate thermal effects, residue, and dimensional changes at the actual thickness and cut geometry. Establish cutting speed and quality through those trials, independently of weld-joint results. This keeps the source evaluation tied to the specific manufacturing task.
Begin qualification with representative resin grades, thicknesses, and joint geometries. Vary power, scan speed or exposure time, focal conditions, and fixture settings in a controlled trial plan. Retain the complete conditions with each result.
Evaluate the joint against its mechanical, sealing, dimensional, and appearance requirements. Cross-sections can help assess the heated region and defects where relevant. Repeat accepted conditions across representative parts and expected manufacturing variation.
Measure the complete cycle, including loading, clamping, positioning, laser exposure, cooling, and release. This establishes throughput for the manufacturing operation rather than only the beam-on interval.
Finalize the source configuration after defining the usable power range, installation conditions, and acceptance criteria. Retain the qualified recipes and material specifications as the baseline for production equipment and later changes.
Choose a continuous wave fiber laser source by matching material absorption, delivered power, and exposure to the required joint performance. A validated thermal process provides the basis for selecting the configuration and completing the equipment design.
Email Intl@menovex.com with your polymer grade, thickness, joint or cutting geometry, target cycle time, and cooling constraints to discuss a Menovex 1940 nm configuration and request detailed specifications.
Related news recommendations
...